How To Read Degrees On A Plat Map

Consider which format you want to use. The corners of your plat map will have the book and page number.

The 32 Points of the Compass Compass points, Compass

To better understand this concept, imagine that you are facing north.

How to read degrees on a plat map. Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a. The angle can be stated as a certain number of degrees (°), followed by an additional number of minutes ('), followed by a certain number of seconds (). Thence n 89 degrees 54’41” w, 314.69 feet to the east line of a 20 foot easement;

To read the coordinates of any location, start with the number of degrees on the latitude line, and clarify whether it is in the northern or southern hemisphere. Directly to your right (east) would be 90 degrees east of north. An example heading might be n63e.

For millimeters, divide the large number on the map scale (i.e. This can be read more descriptively as north 66 degrees 0 minutes and 0 seconds for a distance of 1245.01 feet. The angle is calculated as degrees+minutes/60+seconds/3600.

If your map shows seconds, find the second closest to where each line intersects the latitude or longitude scale at the edge of the map. If you turned around you would be facing south and would be 180 degrees south of north. Learning to read a land survey map is not only for surveyors.

Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass. Thence run n 0 degrees. As you continue to turn you would face west, located 90 degrees west of north.

This reads north, 63 degrees east. surveyors can mark the compass degree system as precisely as they want. Since south from there would be 180 degrees, 36 degrees does not make much sense. Our compass puts north at 0 degrees.

You probably remember from school that a circle is 360 degrees, a degree is 60 minutes and a minute is 60 seconds. A plat is a map of a land area, usually on the scale of a neighborhood or county township, and a plot is a piece of land used for a single purpose (such as a park or a home). These are usually drawn and then each line is annotated with bearing and distance.

The plat is actually based on a previous plat drawn in 1850 so you're another 2 degrees off. 4 degrees of error down one side of your parcel equates to about a 460' error in where you think the property corner should be. Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management.

This is then converted to cartesian degrees by the nested if/then. The earth is nearly 25,000 miles around, so once divided into 360 degrees, it means each degree is about 69 miles wide. For our 1:9,000 map example, the millimeter divide by number equals 1.8 (1 millimeter = 1.8 poles).

The second format is degrees, minutes and seconds: You read an old plat from the 40's with metes and bounds rounded to the nearest degree. How to read a land survey map.

The elements of a list or a tuple are indexed by a number starting with zero. A map’s scale provides a ratio of map distance to actual distance. Thence continue s 0 degrees 03’08” e, 409.67 feet;

100,000.” this ratio simply means that 1 unit of distance on the map is equal to 100,000 units in real life. A site plan package can include: Now click on the other parcel corners that interest you to see those coordinates.

Survey plats can also be read in reverse. For inches, divide the large number on the map scale (i.e. Land survey maps are used to measure everything from.

An example of bearing and distance might be n 66° 0′ 0″ e 1245.01′. So if 'q = deedpoints[0]', then 'q[0] = n' and 'q[5] = 1401.09'. N42w, or 42 degrees west of north;

For our 1:9,000 map example, the inches divide by number equals 45.5. The scale will differ from map to map, but will typically be presented as a number ratio, like “1 : The scale of your plat map will be in the map’s legend.

The scale will be the ratio between the distance on the map and the distance of the actual property. Use a ruler to get the most accurate reading of your plat map. Click on the remaining corners.

So, to make our heading work, we need to add 36 to 180, giving us 216 degrees. This will give you an idea of just how far you have to go. Sometimes a client will note that measured bearings and distances vary somewhat from the recorded measurements shown within the deed or on the plat.

A survey bearing indicates the quadrant in which it exists and the number of degrees into that quadrant measured from zero. Deedpoint is a list of tuples, while 'd' is a tuple. I prefer the decimal format.

Site plan is a drawing that is a bird’s You miss figure the declination from the magnetic bearing shown on the plat by 2 degrees. For example, if your latitude line falls about 5″ above the 32°20′n line, your point is at a latitude of approximately 32°20′5″n.

Each degree is then broken down into 60 minutes. The distances are usually indicated in u.s.

Global Geographic information system (GIS) Market